Click
Here to 
How To Test your Water At Home!
Do It Yourself with Watersafe® All-In-One Test Kit
Order Today $19.95 (Free Shipping)
You can also test for Lead or Bacteria individually.
This simple do-it-yourself water testing kit allows you to check your drinking water for eight common contaminants. It’s fast and accurate as a lab!
This do-it-yourself test kit allows you to check your drinking water for eight common contaminants: Bacteria, Lead, Pesticides, Nitrates, Nitrites, Chlorine, pH and Hardness. Watersafe test kits are accurate, easy-to-use and produce results on the spot.
Product Description:
This Watersafe® Test Kit contains everything
you will need to find out simply and accurately if your water contains unsafe
or undesirable levels of one or more of 8 common contaminants. Follow instructions
carefully and compare results to the desired values below. Drinking water which
tests outside the desired values may be dangerous to your health.
Watersafe® All-in-One Instructions
The Watersafe Test Kit contains everything you need to find
out simply and accurately if your water contains unsafe or undesirable levels
of 8 common contaminants. Follow the instructions carefully for each test,
and compare results to the desired values.
Drinking water which tests outside the desired values may
be dangerous to your health.
Water Test Desired Value
EPA maximum contaminant levels or guildline standards
| Bacteria | None |
| Lead | Below 15 ppb |
| Pesticides | Below 3ppb (atrazine), Below 4ppb (simazine) |
| Nitrite | Below 1.0 ppm |
| Total Nitrate/Nitrite | Below 10.0 ppm |
| Total Chlorine | Below 4 ppm |
| pH | 6.5 to 8.5 |
| Total Hardness | 50 ppm or less |
Before you begin...
1. Contents:
- One Bacteria Test Vial
- One Lead / Pesticide Test Packet
- One Nitrate / Nitrite Test Packet
- One pH / Hardness / Chlorine Test Packet
2. Keep tests out of reach of children or pets. Do not ingest
anything from this test kit. Do not drink water sample used for testing.
Store and use at room temperature (60-86 F).
Do not use on hot water or water containing bleach detergents. Do not re-use
any part of the test kit.
3. Do not open packets or vial until you are ready to perform the tests.
4. Read and follow all instructions carefully.
Bacteria Test Instructions
Purple: Negative Result (No bacteria were detected). |
Yellow: Positive Result (It is highly
likely that potentially harmful bacteria were detected). |
 |
 |
1. Take out the Bacteria Test vial and set upright
on a flat surface.
2. Collect water sample or turn on tap to a very slow stream.
3. Carefully twist off cap and fill vial to 1/2 inch below the top (to 5 ml
line). DO NOT OVERFILL and DO NOT SPILL the bacterial growth powder in the
vial.
4. Replace cap and twist on tightly. Shake the vial vigorously for 20 seconds.
5. Place the capped vial upright in a warm area (70-90 F) where it cannot be
disturbed for 48 hrs.
6. After 48 hrs., observe the color of the liquid without opening the
vial.
7. For positive results, add bleach to the sample before pouring down the toilet,
then wash hands carefully. Negative samples may be poured directly into the
toilet. Discard vial in the trash.
Lead / Pesticide Test Instructions
The Watersafe Lead Test can detect dissolved lead at levels below the EPA Action level of 15 parts per billion (ppb). The Watersafe Pesticide Test detects two of the most common pesticides used in the US at or below the EPA Maximum Contaminant Level (atrazine - 3 ppb, and simazine - 4 ppb).
If you only see the LEFT line (next to number 1), the
test is negative) |
Positive: The RIGHT line (next to number 2)
is darker than the LEFT line (next to number 1), or lines are equally
dark (Both LEFT and RIGHT lines are equally dark) |
1. Open Lead / Pesticide packet and take out all contents. The packet contains
a test vial, a dropper pipette, two Watersafe test strips, and a desiccant
(to be discarded).
2. Using dropper, place exactly TWO dropper-fuls of water sample into
test vial. To pick up the sample, tightly squeeze the bulb at the end of the
dropper and place the open end into the water sample. Release the bulb to pick
up the sample, then squeeze again to expel the sample into the vial.
3. Swirl vial gently for several seconds. Place on a flat
surface.
4. Place both test strips into the test vial, with arrows
pointing DOWN.
5. Wait 10 minutes. Do not disturb strips or vial during this
time. Blue lines will appear on the strips.
6. Take the strips out of the vial and lay them on a flat
surface with the arrows pointing to the LEFT.
Read Results.
7. Note: If no lines appear, or both lines are very light, the test did not
run properly and the result is not valid.
If a test strip shows a positive result, your water sample may contain lead
or pesticides at a toxic level.
Nitrate / Nitrite Test Instructions
1.Carefully open Nitrate / Nitrite Test packet and take out
test strip.
2. Immerse the reagent pads into water sample for 2 seconds, remove, after
1 minute match colors with the chart below.
3. Colors are stable for 1 minute.
Total Nitrate/Nitrite (as N) (end pad)
Nitrite (as N) (pad nearest handle)
pH | Hardness | Chlorine Test Instructions
1. Carefully open pH/ Hardness/ Chlorine Test packet and take
out test strip.
2. Immerse the reagent pads into the water sample and remove immediately. Hold
the strip level for 15 seconds.
3. Match pH,Total Hardness and Total Chlorine Pads (in that order) to the color
chart below.
pH (end pad)
LR Total Hardness (middle pad)
Total Chlorine (pad nearest handle)
Note: If your water tests outside the desired values, call 888.438.1942.
Please note that Watersafe® is a screening test and can not be used to certify water as safe or unsafe for drinking. Watersafe® provides approximate results ONLY when used in strict accordance with instructions. Silver Lake Research Corporation expressly disclaims any liability resulting from the use of this product, failure to follow instructions, or reliance of test results.
WHY WATER TESTING ?
Watersafe® Drinking Water Tests Kits are affordable (under $20), fast (ten minutes from start to finish) and yield reliable, lab-accurate results.
Despite modern facilities, water remains an all-too-common
source of both acute and chronic illness – simply because it is by far
the most ingested substance on the planet.
Chronic exposure to chemical contaminants is particularly dangerous and these
toxins are highly insidious, causing damage over months and years, often with
serious or deadly effects. Water contaminants can be man-made or naturally
occurring.
The E.coli bacteria is responsible for an estimated 73,000 cases of infection and 61 deaths per year in the United States (Center for Disease Control and Prevention).
Chlorine, used for disinfection, can react with organic matter to form cancer-causing trihalomethanes.
Pipes can leach lead, which causes a wide variety of systemic and developmental problems. Until 1988 pipes and fixtures containing lead were used in construction. Most homes and offices built before then may have lead-containing pipes and fixtures in current use.
Pesticides have been discovered in every large watershed in the US and in a large percentage of groundwater wells.
In the US about 1,000,000 children under the age of six have a blood lead level exceeding the level of concern.
Do It Yourself with Watersafe® All-In-One Test Kit |
$19.95 |
How To Test Your Water for Lead! Simple 10 minute results!
Watersafe® Drinking Water Lead Test Kit
Order Today $ 9.95 ea.(Free Shipping)
We like the All In One Kit, but if you are only interested in testing for lead, this kit gets very high marks. Take 10 minutes to protect your family from the damaging effects of lead poisoning. Detects dissolved lead at the EPA Action Level of 15 parts per billion.
This is one test you don’t want to miss . . . either
by testing for lead in the All In One Kit or for lead alone, because there’s
nothing more important, learning disabilities, kidney damage, muscle disorders
and more have all been linked to lead consumption.
The Watersafe® Lead Test can detect dissolved lead at
levels below the EPA Action level of 15 parts per billion (ppb).
The Watersafe® Lead Test can detect dissolved lead at levels below the
EPA Action level of 15 parts per billion (ppb).
Lead Test Instructions
If you only see the LEFT line (next to number
1), the test is negative) |
Positive: The RIGHT line (next to
number 2) is darker than the LEFT line (next to number 1), or lines
are equally dark (Both LEFT and RIGHT lines are equally dark) |
1. Open Watersafe® foil packet and take
out all contents. The kit contains one Lead Test strip, one sample vial, and
one dropper pipette, as well as a desiccant packet (to be discarded).
2. Using dropper pipette, place water sample in the test vial. To pick up sample,
tightly squeeze the bulb at the end of the pipette and place the open end into
water sample. Release the bulb to pick up sample into vial. Use only one pipette-full
of water. Swirl vial gently for several seconds. Place vial on a flat surface.
3.
Place the Watersafe® test into test
vial, with arrows pointing down.
4. Wait 10 minutes. Do not disturb strip or vial during this time. Blue lines
will appear on the strip.
5. Take the strip out of the vial and read results.
6. Note: If no lines appear, or both lines are very light, the test did not
run properly and the result is not valid. If a test strip shows a positive
result, your water sample may contain lead at a toxic level.
Note: If your water tests outside the desired values, call the Safe Drinking
Water Hotline at 1.800.438.1942.
Please note that Watersafe® is a screening test and cannot be used to certify
water as safe or unsafe for drinking. Watersafe® provides approximate results
ONLY when used in strict accordance with instructions. Silver Lake Research
Corporation expressly disclaims any liability resulting from the use of this
product, failure to follow instruction, or reliance of test results.
Watersafe® Drinking Water Lead Test Kit |
$9.95 |
How To Test Your Water For Bacteria!
Do It Yourself with this simple 48 hour results!
Watersafe® Drinking Water Bacteria Test
Order Today $ 9.95 ea (Free Shipping)
How pure is your drinking water? Since contaminated water may not smell or taste bad, the presence of potentially harmful bacteria often goes undetected. Put your water to the test with this simple do-it-yourself test kit.
Product Description:
An EPA based test to check for the presence of Coliform
Bacteria in your water.
The presence of bacteria in drinking water is usually a result of a problem
with the water treatment system or the pipes which distribute water, and indicates
that water may be contaminated with germs that can cause desease.
Product Instructions:
1. Contents:
- One Bacteria Test Vial.
2. Keep tests out of reach of children or pets. Do not ingest anything from
this test kit. Do not drink water sample used for testing.
Store and use at room temperature (60-86 F).
Do not use on hot water or water containing bleach detergents. Do not re-use
any part of the test kit.
3. Do not open packets or vial until you are ready to perform the tests.
4. Read and follow all instructions carefully.
Bacteria Test Instructions:
Purple: Negative Result (No bacteria were detected). |
Yellow: Positive Result (It is highly
likely that potentially harmful bacteria were detected). |
|
|
1. Take out the Bacteria Test vial and set upright on a flat
surface.
2. Collect water sample or turn on tap to a very slow stream.
3. Carefully twist off cap and fill vial to 1/2 inch below the top (to 5 ml
line).
DO NOT OVERFILL and DO NOT SPILL the bacterial growth powder in the vial.
4. Replace cap and twist on tightly. Shake the vial vigorously for 20 seconds.
5. Place the capped vial upright in a warm area (70-90 F) where it cannot be
disturbed for 48 hrs.
6. After 48 hrs., observe the color of the liquid without opening the
vial.
7. For positive results, add bleach to the sample before pouring down the toilet,
then wash hands carefully. Negative samples may be poured directly into the
toilet. Discard vial in the trash.
Note: If your water tests outside the desired values, call 888.438.1942.
Please note that Watersafe® is a screening test and can
not be used to certify water as safe or unsafe for drinking.
Watersafe® provides approximate results ONLY when used in strict accordance
with instructions. Silver Lake Research Corporation expressly disclaims any
liability resulting from the use of this product, failure to follow instructions,
or reliance of test results.
Watersafe® Drinking Water Bacteria Test Kit |
$9.95 |
FDA Disclaimer: These statements have not been evaluated by the Food and Drug Administration and these products are not intended to diagnose, treat, cure or prevent any disease. This is not medical advice and is not intended to replace the advice or attention of health care professionals. Consult your physician before beginning or making any changes in your diet, supplements or exercise program, for diagnosis and treatment of illness or injuries, and for advice regarding medications.
Copyright © 2011 YourNatureStore.com /
BioGro Products LLC
All Rights Reserved
This material may not be copied, published to
other media or rewritten in any form without written permission. Use of this
site signifies your agreement to the terms of service.
Site designed by:
Your Web Developer
Site modified by:
Your Nature Store